Whether it's a custom build or just a replacement, these hubs are the foundation for a high-quality wheelset. Dust off that truing stand for a fresh wheel build. - Rapid Drive 108 fat bike hub set with Oil Slick finish - 32 hole, 6-bolt disc - 150X15 Front / 197x12 Rear - Rear hub is equipped with SRAM XD driver, additional freehubs available

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

- Kick-shift 2-speed hub - Coaster brake - Benefits include its simple backpedal-action shifting/braking and no cables or shifters - 6061 aluminum hub shell with 13/32" slotted solid axle (162mm overall axle length) - Gear ratio range of 138% - Includes 22 tooth 3-spline cog - 116mm OLD (over-locknut dimension)

The Fat Conversion Rear hub provides the ultimate in fatbike hub versatility by allowing hub conversion between quick-releases and thru-axles. 170/177mm features - Convertible 10 x 170mm QR/12 x 177mm Thru-Axle spacing - Four sealed cartridge bearings - Serviceable three-pawl freehub mechanism - 58mm flange diameter, right center to flange: 37mm, left center to flange: 44mm - Thru Axle and Q/R Conversion end caps included - 170mm Flip-Off skewers included - XD freehub and conversion caps also available separately 190/197mm features - Convertible 10 x 190mm QR/12 x 197mm Thru-Axle spacing - Four sealed cartridge bearings - Serviceable three-pawl freehub mechanism - Thru Axle and Q/R Conversion end caps included - Flip-Off skewer not included - 422 grams

Boost Centerlock front hubs are designed as precision mountain tools. Featuring a one-piece axle to provide a stiff hub with rail accurate steering. To thwart mud, water, and contaminants as you power through rough trails, Boost Centerlock hubs have heavy-duty bearing seals and snaprings, that provide superior protection with ultra-low drag. - Wide flange placement - Fits 110x15mm Boost spacing - Easily serviceable with a T10 Torx and pick or pen knife - Engineered, manufactured, and assembled in Portland, Oregon USA with King Lifetime Warranty - Hub Drilling: 28 - Hub/Brake Compatibility: Center-Lock Disc - Color: Black - Spoke Interface: J-Bend - Front Axle: 15mm Thru x 110mm

- For 37-590 ISO tires only (TIRE2625) - 26x1 3/8 North American size (E.A.3 British Rim/650A French)

Replacement axles for Manitou forks

The Deadbolt Ultralight Thru-Axles are offered in a 6mm flat button head design, for a flush, clean look. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications - 6mm hex wrench required for installation

Shimano XT FH-M756 Series Rear Hub - Double contact bearing seals - Super polished bearing races for low friction rolling - Light alloy QR lever and nut - 6-Bolt rotor mount - Bearing Type: Loose Ball - Cassette Body Type: Shimano/SRAM 8, 9, 10 Speed - Center to Flange, Left: 33.5 - Center to Flange, Right: 20.5 - Flange Diameter Left: 61 - Flange Diameter Right: 61 - Hub Drilling: 32 - Hub/Brake Compatibility: 6-Bolt Disc - Rear Axle: QR x 135mm - Skewer Included: Yes - Spoke Interface: J-Bend - Weight: 495 grams

Upgrade or refresh your bike. GENUINE REPLACEMENT PARTS When it's time to refresh your trusty bike, Trek Genuine Replacement Parts have you covered. PRODUCT DETAILS - Original equipment replacement for Bontrager Kovee TLR wheel - Convert to tubeless with TLR rim strip and valve, sold separately - Durable alloy symmetric rim with 22.5mm internal 27mm external width - Double wall alloy rim (27mm outer, 22.5mm inner width) - Does not include skewer, reflector, rim strip, valve, or owner's manual - Wheels shipped as photographed

My Other Brother Darryl is a single-wall constructed, 80mm wide rim. 80mm wide rims give you a bigger footprint than that of narrower rims, which means more floatation and more traction. To initiate tubeless sequence, you just need a no-stretch rim strip and bead-to-bead tubeless rim tape. My Other Brother Darryl comes with either a 32 hole, symmetric wheel lacing spoke hole pattern or the tried and true 64 dual spoke hole pattern that allows for symmetric or offset wheelbuilds. It's got plenty of cutouts to keep the weight down and help your tires float through the squishiest of terrain. - Wheel Size: 26 - Hub Compatibility: 32h - ETRTO*: 559mm - Weight: 710g (Symmetric) 740g (Dual) - Color: Black or polished silver *Tire bead seat diameter.

The pinnacle among the hubs–Ratchet EXP united with SINC ceramic bearings. The premium 180 hub convinces with its sophisticated Ratchet EXP technology, giving the hub extra lightness, stiffness, and precision along with easy, no-tool maintenance. Furthermore, assembled with the low-friction SINC ceramic bearings, the hub performs efficiently and brings your power directly to the road. The hub is available for straight pull spokes only.

CRC 1400 Spline wheels are ready to conquer the harshest conditions with convenience. Never mind if the conditions are windy, muddy or rainy, the CRC 1400 Spline is ready to conquer them all. The aero-optimized rim supports your high speeds on descents and on the hunt for your competitors, no matter where the wind blows. The rim profile is tubeless ready, allowing you to take advantage of the technology and simply and conveniently change the tires according to the prevailing conditions of the track. This will ensure you always find the sweet spot between traction and rolling resistance. - Full carbon tubeless ready rim, laced to a straight pull 240s based hub - Tubeless tape 25mm - Tubeless valve road 32mm

Upgrade or refresh your bike. GENUINE REPLACEMENT PARTS When it's time to refresh your trusty bike, Trek Genuine Replacement Parts have you covered. PRODUCT DETAILS - Original replacement wheels for Electra bikes - Does not include skewer, reflector, rim strip, valve, or owner's manual - Wheels shipped as photographed

A rock-steady classic for road riding. - 18mm inner width - Professional tubeless tape installation included

The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples

When motor assistance and leg power meet, the range of terrain a bike can conquer grows almost exponentially. The H 1900 SPLINE is designed for this, now upgraded with the famous DT Swiss Ratchet technology. The Ratchet LN system distributes the combined forces from the rider and the motor over a larger area than the previous pawl freehub systems, increasing the systems’ durability thanks to lower load peaks. The 370 hub enables full power transmission to the ground with reinforced hybrid spokes laced to a resistant aluminum rim, available in two inner widths. - Aluminum rim, Hooked / Crotchet tubeless ready - DT Hybrid 1 spokes are reinforced and increase the lateral and torsional stiffness of the wheel - 370 Hub - Includes Tubeless Valve and Tape, 6-bolt adapter with lockring

- Designed, tested, and raced to victories on the World Cup DH and Enduro World Series circuits - Tie beam triple-cavity rim design resists damage and prevents air loss under impacts - 29mm internal width optimized for 2.35" to 2.8" Trail, All-mountain, and DH tires - E-sync hubs Specs: - Wheel Tire Type: Tubeless Ready - Wheel-Brake Comp.: Disc IS 6-bolt - Rim Material: Aluminum - Spoke Type: Sapim D-Light - Valve: Presta - Rim Construction: Double wall

- Light enough to take XC racing but was born from research and testing on the Enduro World Series circuit, making it a great rim for anyone looking to improve both descending and climbing - Asymmetric rim design allows for a stronger wheel while offering the easy inflation and Stan's trademark unmatched airtight seal. - 28mm internal width ideal for 2.2-2.5" tires - Light and durable 6069 aluminum with welded joint and reinforced spoke bed

Ultra light bolt on thru axle, with a low profile 6mm head for Whisky forks and some others. See other manufacturers specifications for fitment questions. - Thread Length (mm): 12 - Thread Pitch: 1.5 - MT/CX: 125 x 15mm - MTB+: 135 x 15mm - Fat: 198 x 15mm - RD/CX: 120 x 12mm - Rear: 167 x 12mm

Industry Nine Hydra Classic hubs are the heart of your wheelset, everything revolves around them, literally. Every Classic Hydra hub is made start to finish in Asheville, NC. From turning and milling bar stock 7075-T6 aluminum for shells, axles and encaps, wire EDM cutting A2 tool steel for pawls and driverings, to in-house anodization lab, every step of design, engineering, manufacturing and assembly is done to exacting standards. - 690 P.O.E. Hydra Freehub body engages every .52 degrees yeilding telepathic control - 6 pawl, 6 phase - 115 tooth drivering - Easily serviced with no proprietary tools. Designed to keep you in the saddle and out of the service queue - Classic j-bend spoke interface - Steel cartridge bearings are durable

Whether the goal is a finish line, epic adventure or simply getting back home again, SRAM'S 900 hubs are ready for the challenge. On the inside, the smooth and durable DOUBLE TIME drive mechanism ensures rapid engagement for quick and confident pedal responsiveness. SPEEDBALL bearings provide smooth, long-lasting rotation performance. Multiple spoke-count and cassette-capability options, as well as interchangeable end caps, make the 900 hubs a perfect choice for any disc-equipped road, gravel, cyclocross, cross country, trail, or enduro bike. - Versatile driver body can accept ROAD or MTB drivetrain, full spline or XD cassettes - Fully convertible with tool-free end caps - BOOST variants - 24, 28 or 32 spoke holes

You like gravel and wide tires? This is your rim. The GR 531 is made for off-road adventures. This aluminum gravel rim with an inner width of 24mm is designed for wide, knobby tires up to 53mm. Torsion-resistant and robust, the welded rim supports a wide range of gravel use.

Your entire focus lies on the right line choice, the exact braking point and the spot-on steering movement. All the everyday stress fades away, you feel free and only hear the precise sound of the freehub system. The E 1900 Spline wheels were developed precisely for these freewheeling moments. A proven aluminum rim and hand-laced steel spokes provide the reliability required from an Enduro wheel. - Intended use = All-Mountain/Trail, Enduro and Freeride - Tubeless ready, 30mm wide and light rim - Straight-pull hubs/spokes built with a 3-cross pattern - Includes Tubeless Valve and Tape

This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum

This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - One 264mm spoke = 6g - Nipples sold separately

Shimano XT FH-M8010/M8000 Rear Hubs. - Double contact bearing seals - Super polished bearing races for low friction rolling - Shimano Quick-engagement freehub - Not compatible with Shimano 11-Speed Road cassettes - Cone bearings races ground by a Cubic Boron Nitride tool for smooth-rolling durability - Center Lock disc brakes provide reliable braking power (lockring sold separately)

Build your singlespeed or fixie bike around Surly's Ultra New Roadie Rear Hub. This gorgeous hunk of aluminum has the capability you need and reliable sealed bearings, too! It sports threads for a track cog and lockring on one side and a freewheel on the other so you can decide how you want to roll. Plus, this hub's 130mm width fits most road frames and the hollow chromoly axle provides a flex-free ride as well as simple quick release skewer compatibility.

- TSE design with 23mm internal width with tubeless and hookless rim profile ideal for wider tires at lower tire pressure - Minimum 25mm tire width - More than 300 g lighter than previous model - ZR1 DB hub is engineered in Germany with better seal design for improved durability and quicker response with 66 points of engagement - An all-out aero 80mm rim profile - ABLC Sawtooth dimple design helps manage air flow around the rim, and contributes to create a faster, more stable wheel - Center locking rotor interface. Lockring is included - Lifetime warranty

Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go! - For Downhill, Enduro and Road tires - Seals tears and holes up to 6mm - Contains UV puncture detection - Won't dry out or ball - Works from 15psi-120psi and temperatures from -20°C to +50°C - Biodegradable